I spent much of my spare time in the month of October building these.
I was e-mailed by a friend who wished to purchase some for the EF All Souls Mass around the end of September. A quick web search turned up a design that was acceptable, and I made a prototype out of scraps I had lying around the garage. The friend suggested a possible colour scheme which I tried out...
Around this time, I mentioned to a co-worker that I had this commission, and he offered me the use of his duplicating attachment for the lathe. That would make everything so easy and just perfect. I wrote to the buyer and told him that it looked like everything was just hunky dory, and there should be few problems from here on in.
The co-worker wrote to me to tell me that his garage is such a mess that he couldn't get into it enough to find the duplicator. I wrote back to him thanking him for the offer of help, and telling him I would send over the crew from Hoarders posthaste. Inside I was a little annoyed. I would have to freehand the whole thing.
I began by setting up a couple of storysticks. A storystick is basically a stick with the measurements laid out on it. I hold it up against the piece on which I am working, and take the measurements off it, rather than, say, using a measuring tape every time. It is more useful than a measuring tape, as it is more stable, and, if a mistake has been made in the measuring on the stick, it will be a consistent mistake- and in making six identical as possible candlesticks, consistency is more important than accuracy. With a measuring tape, there would b a chance of a random error creeping in to my measurements on every individual piece. I also set my calipers, sharpened my turning tools (since I was working in oak, I would be doing a lot of sharpening over the course of this project) mounted the wood, and fired up the lathe.
I turned the main blank round, and transferred the marks from the stick onto the blank. The only real problem now would be variations about the thickness of a pencil line. A pencil line is about a thirty second of an inch wide, depending on sharpness etc. A deviation about the thickness of a pencil line is not too much of a problem, as it tends to be offset by other deviations. What that means in practical terms is that if you are off- say, too short- by a pencil line thickness for one detail, you are just as likely to be off in the other direction- say, too long- for the next one, and the two deviations will cancel each other out.
Sometimes the deviations line up in the same direction. So if you make four lines, and are off the thickness of the line the same way each time, the error accumulates and instead of cancelling each other out, you will ultimately be off by an eighth of an inch, which is a much greater variation than it sounds. At least for the maker, of which I will say more later.
This problem really appeared after the turning was all done and I began to glue up the candlesticks. Two were the same size; the other four were off by an eighth of an inch or more. I cut them apart, reglued them. The four were now correct. The other two were off, so I sawed them apart, etc. I also noticed that one of the top pieces was unacceptably off. I glued up another blank, and made a better one. Next I had to make sure they all stood up straight.
This was tricky. Because of the height of the candlesticks, being out of true, even by a very small amount, would create a noticeable tilt in the sticks. This is where the feet on the sticks come in. I can plane a little bit off here and there off the feet to make the sticks stand up straight. Except that no matter what I do, the sticks are always tilting a little. And then I notice that, no matter what I do, the sticks are always tilting in the same direction, depending on which section of floor I have put them, which brings me to
The floors in my house are not level. Unless I can find a flat patch in the house, I cannot true up the sticks. I find a flat patch in the kitchen, so, huzzah, but then I realize that, with all the adjusting I had done trying to get them to stand up straight in the living room, I had more or less ruined the feet. So, remove feet, and put on a new set. A very small amount of adjustments later, and everything is hunky dory. The sticks were now ready for finishing.
The finishing process actually went quickly and smoothly. Three applications of stain (I used a water based aniline dye, dark walnut colour. One of my gloves leaked, and the dye soaked into my skin, and it was impossible to get off. My hand was dark brown for over a week until the skin die and flaked off.) and another five of varnish. Apply thin coats, sand in between, and voila, the job is finished. Call up the buyer.
This is mainly psychological. As a builder, I know every flaw and misstep in my work. To me, it stands out like a sore thumb, and I see the flaws every time I look at my work. No one else ever sees it, but I do, and it makes me a little paranoid sometimes. I find myself thinking, he'll see it. He'll hate it. He won't pay. I don't blame him.
But it was all for nothing. The buyer came, loved them, and picked them up. He even sent me a photo from the All Souls Day Mass.
Now, back to the Christmas Bazaar stuff, and the home altar, and the medieval clock, and the hope chests, and the desk, and....